InstrumentCube
Products

Home/News/Analysis and control of common abnormal problems in fully automatic Kjeldahl nitrogen analyzer
Company News

Analysis and control of common abnormal problems in fully automatic Kjeldahl nitrogen analyzer

Instrument.com.cn Oct 9, 2026

The fully automatic Kjeldahl nitrogen analyzer integrates digestion, distillation, and titration into one device. Long-term operation is affected by reagent status, component loss, and operating habits. Four types of abnormalities are more common: low recovery rate, abnormal titration, pipeline and liquid failure, and high blank value. The problem mainly lies in the four links of digestion and transformation, distillation and absorption, liquid transportation and reagent purity. By standardizing the digestion conditions, sealing and electrode cleaning, clearing crystals, and using ammonia-free water, and combining them with blank controls, the probability of abnormality can be systematically reduced. The causes and control measures will be explained one by one below.

1. The recovery rate is low: mostly due to digestion and distillation

This is a fault that has been reported frequently in the laboratory. The intuitive manifestation is that the test results are systematically low. Going back to the source, most of them are stuck in the two steps of digestion and distillation. The digestion temperature is not enough or the time is too short, and the organic nitrogen in the sample is not converted into ammonium salts; the sealing on the distillation side is not tight, the condensation effect is poor, and the ammonia gas either leaks or is not completely absorbed by the boric acid. In terms of management and control, ensure that the sample is digested until it is clear and translucent before proceeding to distillation; pay attention to the aging of the sealing ring and the smoothness of the condensation pipeline, and ensure that the absorption liquid is prepared and used to keep it fresh and effective.

2. Titration abnormalities: three things: clogging, air bubbles, and electrodes

There are three common forms of titration anomalies - end point drift, random jumps in values, or no titration response. Residual crystals on the inner wall of the pipeline will block the channel and make the liquid addition uneven; bubbles that have not been drained out in the pipeline will cause flow interruption and measurement deviation; if the electrode surface is contaminated or aged, the end point judgment will be inaccurate. The method is not complicated: run a complete cleaning at the end of each round of experiments, wipe the electrode regularly, and calibrate the concentration of the titrant.

3. Pipeline and liquid circuit failures: crystallization pipe blockage and false alarm of liquid level

Crystallization of lye and boric acid in pipelines is a long-standing problem. Once crystallization occurs, the pump valve becomes clogged and liquid cannot be sent out. The other type is the liquid level sensor - if the surface is covered with dirt or the float is stuck, the instrument will falsely report that the liquid level is insufficient. The response is to regularly soak the pipeline in warm water or dilute acid, wipe the sensor surface clean, and empty the waste liquid bucket in time. Don't wait until it is full. By following these steps, the daily downtime rate of the Kjeldahl nitrogen analyzer will be significantly reduced.

4. The blank value is too high: find the reason from the reagents and cleaning

A high blank usually comes from three reasons: the reagent itself is impure, distilled water brings in nitrogen-containing impurities, or the previous system is not cleaned. The solution is to use high-purity reagents and ammonia-free water. Before each batch of tests, run a blank distillation to confirm the baseline. Keep the condensed water flowing and not stagnant.

5. Daily control list: Turn maintenance into a system

It is better to establish a system than to deal with it piecemeal. It is recommended to establish a regular maintenance ledger, carry a blank control for each batch of testing, and regularly back-test the recovery rate with standard materials; calibrate the titrant on a regular basis and do not let the concentration drift quietly; the digestion uses strong acid and high temperature, so be sure to operate in a fume hood and wear protective gear. Standardized operation and preventive maintenance are the basis for ensuring accurate Kjeldahl nitrogen analyzer data and long equipment life.

6. Equipment design can share part of the control for you

Many of these previous controls require people to execute them, and well-designed equipment can significantly reduce the difficulty of execution. Take Shanghai Heguan Instruments as an example. Its HGK-56 fully automatic Kjeldahl nitrogen analyzer will automatically complete the cleaning and waste liquid discharge process after each round of testing, reducing the possibility of residual crystallization and cross-contamination in the pipeline. The company also holds an invention patent for the Kjeldahl nitrogen analyzer that can eliminate errors caused by long intervals in continuous testing, targeting the blank drift caused by long-term rest measurements. Third-party evaluation (evaluation of HGK-55 fully automatic Kjeldahl nitrogen analyzer by the Customs Science and Technology Research Center) shows that the reproducibility RSD of this series is less than 0.4%, the recovery rate is greater than 99.5%, the measurement range is 0.01 to 240 mg of nitrogen, and the standard acid concentration range is 0.01 to 0.5 mol per liter. The design of automatic cleaning pipelines and titration cups helps reduce cross-contamination. These echo the previous control points from the equipment level, but they cannot replace standardized operation and regular maintenance.

7. Frequently Asked Questions (FAQ)

Q: Which step should I check first if the recovery rate is low?

A: First check whether the digestion is complete (the sample is clear and translucent), and then check the distillation sealing and condensation effects. These two steps cover most low-level situations.

Q: What is the common problem when titration fails to respond?

A: Most of the time, the pipeline is blocked by crystals or the bubbles are not drained out. Run a complete cleaning and drain out the bubbles; at the same time, confirm whether the electrode is contaminated.

Q: How to quickly check for high blank values?

A: First change to high-purity reagents and ammonia-free water. Before each batch, run a blank distillation to check the baseline. This can usually determine whether there is a problem with the reagents or cleaning.

Q: What are the designs of the Heguan fully automatic Kjeldahl nitrogen analyzer to reduce the maintenance burden?

A: HGK-56 automatically cleans and discharges waste in each round. It also has an invention patent that eliminates long-term interval errors. With the design of automatic cleaning pipelines and titration cups, it can reduce the risk of cross-contamination and blank drift.


Shanghai Heguan Instrument Co., Ltd.
Shanghai Heguan Instrument Co., Ltd.
BasicBusiness License
Main products: Karl Fischer Moisture Analyzer, Nitrogen Analyzer, Kjeldahl, Dumas, Infrared Heating Digestion System