InstrumentCube
Products

Home/News/Aoying Science | The difference between DR and CT: the "fluoroscopy eye" and "tomography microscope" of non-destructive testing
Company News

Aoying Science | The difference between DR and CT: the "fluoroscopy eye" and "tomography microscope" of non-destructive testing

Instrument.com.cn Oct 9, 2025

Name decryption



DR (Digital Radiography) and CT (Computed Tomography) are the two core technologies in the field of non-destructive testing. Both reveal material defects in a non-destructive way and are widely used in precision industrial fields such as aerospace, automobile manufacturing, and electronic components.



Differences in imaging principles


DR


Penetration method

For a single X-ray irradiation, the detector directly receives the attenuated signal transmitted through the object, forming a "projection (perspective) image" similar to2D image。


information dimension

It only provides planar superposition information at a certain angle of the sample and is extremely susceptible to interference from the overlapping structure within the sample.


CT


Penetration method

During the image collection process, by controlling the precision turntable to continuously and stably rotate the object, the detector collects projection images of X-rays penetrating the object at different angles, and then uses a computer reconstruction algorithm to convert the collected image information into a three-dimensional data model. In the three-dimensional visual analysis software, the three-dimensional data model can be sliced ​​and analyzed in any direction, and information such as the location and size of internal defects can be accurately located. Achieve high-precision "three-dimensional anatomy" of the internal structure of objects in a non-destructive manner.


information dimension

Build a three-dimensional model to obtain the complete digital structural information of the sample, and use professional three-dimensional visual analysis software to analyze and calculate slices layer by layer to accurately obtain detailed information such as defect location, size and spatial distribution, especially suitable for the detection of complex geometric shapes. It is more conducive to more advanced applications such as failure analysis, fault inspection, process improvement, product design optimization, etc. on samples.



Equipment structure and testing process

DR


Equipment composition

The equipment is relatively simple, mainly including a radiation source, a flat-panel detector, a mechanical transmission device and image processing software.


Detection time-consuming

The detection can be completed in a single exposure, which takes a relatively short time and is suitable for rapid screening in the assembly line.


CT


Equipment composition

In addition to the radiation source and flat-panel detector, the mechanical system requires high-precision and high-stability hardware configuration, and requires high-precision debugging and calibration. In addition, higher-performance data acquisition systems, three-dimensional data analysis hardware and software systems are also required, and the cost is significantly higher than that of DR.


Detection time-consuming

Multi-angle scanning and image reconstruction need to be completed, and the inspection time ranges from minutes to hours. Complex workpieces require continuous debugging and optimization of parameters to achieve the best results.



Performance vs. cost comparison

DR


Detection accuracy

The resolution can reach 0.1-0.3mm, and volumetric defects (such as pores and inclusions) can be identified.


Economy

The full life cycle cost of DR (purchase + maintenance + consumables) is relatively low, maintenance is relatively simple, and it is suitable for large-volume testing.


CT


Detection accuracy

The resolution can reach up to nanometer (sub-micron) level, which can identify smaller defects and quantify density differences.


Economy

There are significant differences in the cost level of CT equipment, and operation requires strict environmental control and parameter adaptation, requires professional operation, and has high maintenance costs.



Application scenarios

DR

CT

Weld quality inspection (such as pipes, pressure vessels)

It is widely used in the detection of precision parts and products in aerospace and high-end manufacturing industries, as well as the research and analysis of new materials.

Batch screening of pores and shrinkage cavities in castings

Emerging Additive Manufacturing Product Technology Improvements

Analysis of solder joint defects of electronic components

Detection and analysis of new energy batteries and device products

With its advantages of fast imaging and low cost, DR has become an ideal choice for rapid screening of simple structural components; while the advantage of CT is three-dimensional visualization, which can achieve high-precision dimensional measurement, intuitively display the internal fine structure of the sample, find and solve hidden defects in complex structures, and obtain accurate judgment basis.



Always Imaging Ltd.
Always Imaging Ltd.
BasicBusiness License
Main products: X-Ray Instrument Parts/Operating System, Industrial CT / Micro-CT
Recommended Products